CMPx.MODBOUND1
Description
Use this keyword to set the first modulo bound. CMPx.MODBOUND1 and CMPx.MODBOUND2 must both be set before the modulo functionality can be activated. There is no requirement that the second modulus bound be larger than the first modulus bound.
CMPx.MODBOUND1 must be set before CMPx.SETPOINT.
Example
The following example sets the first modulo bound to one billion counts for CMP1.
-->CMP1.MODBOUND1 1000000000
General Information
|
Type |
NV Parameter |
|
Units |
Units depend on value of CMPx.SOURCE. See table below. |
|
Range |
-9,223,372,036,854,775,808 to 9,223,372,036,854,775,808 |
|
Default Value |
9,223,372,036,854,775,808 |
|
Data Type |
Integer |
|
Start Version |
M_01-13-00-000 |
Units
| CMPx.SOURCE | Units |
|---|---|
| 0 (FB1) | Depends on FB1.PUNIT or custom units. |
| 1 (FB2) | Depends on FB2.PUNIT or custom units. |
| 2 (FB3) | Depends on FB2.PUNIT or custom units. |
| 3 (PL.FB) | Depends on UNIT.PLINEAR or UNIT.PROTARY Rotary: counts, rad, deg, (custom units), 16-bit counts Linear: counts, mm, µm, (custom units), 16-Bit counts |
Hardware Supported
Compare functionality is supported on hardware revisions D, DB, DA, and higher depending on the drive type. Check the label on the side of the drive to ensure the AKD meets one of the following requirements.
| AKD Type | Hardware Revision Supported |
|---|---|
| AKD | Revision D or higher |
| AKD PDMM | Revision DB or higher |
| AKD-T-IC | Revision DA or higher |
Variants Supported
| Variant | Supported |
|---|---|
| AKD Base | No |
| AKD with Position Indexer | No |
| AKD EtherCAT | Yes |
| AKD CANopen | Yes |
| AKD BASIC | Yes |
| AKD SynqNet | See SynqNet Supported Parameters |
| AKD EtherNet/IP | Yes |
| AKD PROFINET | Yes |
| AKD Sercos® III | Yes |
| AKD-N | No |
| AKD-C | No |
*In SynqNet, a parameter may be available in the firmware but have no effect on the system. See SynqNet Supported Parameters.
Fieldbus Information
If your drive type is listed as supported but no index, address, or instance number is listed, then this parameter is accessible through WorkBench, but not over your fieldbus type.
| Index/Subindex | Object Start Version | |
|---|---|---|
| 34A9h/1 | CMP0.MODBOUND1 | M_01-13-00-000 |
| 34B9h/1 | CMP1.MODBOUND1 | |
| Parameter | Fieldbus | Address | Attributes | Signed? |
|---|---|---|---|---|
| CMP0.MODBOUND1 |
PROFINET |
2930 | DWord | Yes |
| Sercos® III | 8 Octets | |||
| CMP1.MODBOUND1 |
PROFINET |
2937 | DWord | |
| Sercos® III | 8 Octets |
| Parameter | Instance | Data Size | Data Type |
|---|---|---|---|
| CMP0.MODBOUND1 | 931 | 8 Byte Signed | Position |
| CMP1.MODBOUND1 | 938 |
| Parameter | Register Address | Is 64 bit? | Attributes | Signed? | Object Start Version |
|---|---|---|---|---|---|
| CMP0.MODBOUND1 | 1860 | Yes | 64 bit | Yes | M_01-03-00-000 |
| CMP1.MODBOUND1 | 1874 |
